Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Each person seems to have his or her own assumption on the subject of Tools You Need to Install a New Bathtub .
Setting up a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough job. If the old tub is readily easily accessible, the job can move easily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have actually certified yourself for the job and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to consider utilizing one before you start. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have actually already gotten a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list ought to consist of the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that write-up about How to Install a Bathtub from a friend on a different web page. Sharing is caring. One never knows, you will be doing someone a favor. Many thanks for your time invested reading it.
Book Service Report this page